Plain answers for DIY tool jobs · Sources listed on every guideNew: Can you use a chainsaw in the rain? →
Newsletter
Updated Nov 6, 2026

How to drill a 4-inch hole in a concrete foundation wall

By Robert D. Miller5 min read
Quick answer Use a 4-inch diamond core bit on a core drill, with water running. It's the DIY tool that cuts a clean round hole through poured concrete and rebar. For concrete block or brick, a carbide core bit on an SDS-max rotary hammer also works. A regular hole saw won't cut concrete. Most people rent the core drill.
A row of twist drill bits in different sizes
Photo: George Chernilevsky, Wikimedia Commons, Public domain
In this guide
  1. Which tool for which wall
  2. Before you drill: four checks
  3. Steps: poured concrete with a wet core drill
  4. Steps: concrete block or brick
  5. If that didn't work
  6. When to call a pro
  7. What you'll need
  8. Questions people ask

A clean 4-inch hole through a poured concrete wall takes a diamond core bit, a core drill and water. It's a rental job for most people. Block and brick walls are easier: a carbide core bit on a big rotary hammer can do it.

This guide is part of our drilling hub. For bits and anchors in masonry, see the concrete and brick page and our main guide on how to drill into concrete.

Which tool for which wall

Wall Tool Bit Notes
Poured concrete, with or without rebar Wet core drill, on a stand or handheld Wet diamond core bit Cleanest hole. Cuts rebar. Needs water and a GFCI
Concrete block (CMU) SDS-max or spline rotary hammer Carbide core bit Fast in hollow block. Stops at rebar
Brick SDS-max rotary hammer, or a core drill Carbide or diamond core bit Drill from both sides to avoid blowout
Any wall, no big tools Hammer drill Ring of small masonry holes, then chisel Rough, slow hole. Fine only under a trim ring
Any concrete Drill with a bi-metal hole saw — Won't work. Wood and metal hole saws can't cut concrete

Before you drill: four checks

1. What's in the wall

Look on both sides for pipes, wires and meters. Gas lines can run through foundation walls, often near the meter. Read what happens if you drill into a gas pipe before you start near one.

2. Is it post-tensioned?

Some slabs and walls have steel cables under huge tension inside. Fire Engineering warns that a cut tendon can release violently, and Concrete Network notes it's very hard to repair.

Some post-tensioned slabs carry a stamp saying so. If you see one, or you aren't sure, don't core it yourself. A coring contractor can scan first.

3. Rebar and the wall itself

Foundation walls usually have rebar. A wet diamond bit cuts through it, slowly. A carbide core bit won't.

Stay away from corners, beam pockets and the edges of windows and doors. If you'll cut several bars, ask a structural engineer. See what to do if you hit rebar.

4. Hole size and height

Code (IRC M1502.4.1, as adopted locally) calls for dryer exhaust ducts to be 4 inches nominal, round. Your hole has to clear the outside of the vent hood's sleeve, not just the duct. Measure the sleeve and choose the core size that fits around it. Keep the hole above outside grade, and check your local code for clearances from windows and doors.

Steps: poured concrete with a wet core drill

Set up

  1. Drill a small pilot hole straight through with a hammer drill and a long masonry bit. It shows you exactly where the core will come out.
  2. Thread the core bit onto the drill. Milwaukee's wet core bits from 2 to 14 inches use a 1-1/4-inch-7 thread.
  3. Mount the drill on its stand and anchor the stand to the wall, or hold a handheld rig with both handles. A stand keeps the bit from walking.
  4. Hook up the water. Plug a corded drill into a GFCI. Milwaukee's cordless MX FUEL core drill skips the cord and has a clutch and AUTOSTOP to stop it twisting if the bit binds.
Safety: A core bit that binds can twist the drill hard. Brace yourself, use the side handle or the stand, and never wrap the cord around your arm. The slurry is slippery, so wear boots, and gloves keep it off your hands.

Drill

  1. Turn the water on before the bit touches the wall.
  2. Start slowly until the bit cuts a full ring, then run at the drill's rated speed.
  3. Feed with steady pressure. Gray slurry should flow out. If it stops, add water.
  4. Back the bit out now and then to flush the cut.
  5. When you hit rebar, the drill feels different and slows. Keep the water on and keep a light, steady feed.
  6. Go halfway, then finish from the outside using your pilot hole as the center. That keeps the outside face from breaking out.

Finish

  1. Knock the core out. If it sticks in the bit, tap the bit's side with a rubber mallet. Don't hit the diamond rim.
  2. Vacuum the slurry with a wet/dry vac.
  3. Fit the duct sleeve or pipe. Seal the gap on the outside with a masonry sealant or hydraulic cement so water can't get in.

Steps: concrete block or brick

  1. Pick a spot over a hollow cell in block, so you only cut the two thin face shells.
  2. Fit a carbide core bit to an SDS-max or spline rotary hammer. Milwaukee's thick-wall carbide core bits are made for brick, block and concrete. The 3-inch one cuts 4-1/16 inches deep and uses a guide plate and centering pin to start.
  3. Use the centering pin or a guide plate to start the hole. Remove the pin once the bit has a groove.
  4. Drill with hammer action on. Use a dust shroud with a vacuum. OSHA's Table 1 calls for a shroud and dust collector on rotary hammers and a HEPA vacuum to clean holes.
  5. Drill halfway, then finish from the other side.

Not sure which rotary hammer you need? Read SDS-plus vs SDS-max and hammer drill vs rotary hammer vs impact driver. The drill bit selector matches bits to the wall.

If that didn't work

  • The core bit stopped cutting. The segments may be glazed: shiny and smooth. Dress them with a few cuts in a soft brick or a dressing stick. The same fix works on blades; see how to sharpen a diamond blade.
  • The carbide bit hit steel and stopped. That's rebar. Switch to a wet diamond core bit.
  • The bit is stuck in the wall. Turn the drill off. Rock the bit gently by hand and flush it with water. Don't yank it with the motor.
  • A bit snapped. Our guide on removing a broken drill bit covers small masonry bits.
  • Water is seeping in around the new duct. Reseal the outside joint, and slope the duct so it drains to the outside.
  • You only need to hang the vent hood now. For screws in the concrete around it, see screw won't go into the wall, which covers masonry screws and bits.

When to call a pro

Call a concrete coring contractor if the wall or slab is post-tensioned, the hole is below grade, you'll cut several rebar, or the hole goes through a footing or beam. They scan for steel first and bring rigs that core big holes fast. For a gas line, a meter or a wire in the way, call the utility or a licensed plumber or electrician.

What you'll need

  • Core drill: Rent a handheld or stand-mounted wet core drill; Milwaukee's MX FUEL cordless version cores up to 6 in in reinforced concrete
  • 4-inch wet diamond core bit (or the size that clears your sleeve): Match the thread to the drill, usually 1-1/4 in-7
  • SDS-max rotary hammer and carbide core bit: Block or brick walls only
  • Hammer drill and a long masonry bit: For a pilot hole to find the exit point
  • Water supply and a wet/dry vacuum: Garden hose or pump can; the vac picks up slurry
  • GFCI outlet or plug-in GFCI: Water and corded tools
  • Safety glasses, hearing protection, gloves, boots: Slurry is slippery
  • Masonry sealant or hydraulic cement: To seal around the duct or pipe

Key takeaways

  • Poured concrete: wet diamond core bit on a core drill. Milwaukee's 4-inch wet core bit is rated for concrete and rebar and fits core drills with a 1-1/4-inch-7 thread.
  • Block and brick: a carbide core bit on an SDS-max or spline rotary hammer is enough. It doesn't cut rebar.
  • Before you drill, check for pipes, wires and gas lines, and look for a post-tension stamp. Don't core a post-tensioned slab yourself.
  • Keep water on the bit. OSHA's silica table pairs core rigs with integrated water. Plug corded tools into a GFCI.
  • For a dryer vent, code calls for a 4-inch round duct. Measure the vent sleeve's outside size and pick a core bit that clears it.

Questions people ask

Can I drill a 4-inch hole in concrete with a hammer drill?

Not cleanly. A hammer drill can't turn a 4-inch core bit. You can drill a ring of small holes with it and chisel out the middle, but the hole will be rough. For poured concrete, rent a core drill.

Will a 4-inch hole saw cut concrete?

A regular bi-metal hole saw won't. It's made for wood and metal and will dull in seconds. For concrete, use a diamond core bit. For block or brick, a carbide core bit on a rotary hammer also works.

What do pros use to cut a 4-inch hole in concrete?

A diamond core drill, usually on a stand bolted or vacuum-held to the wall, with water fed to the bit. Milwaukee's cordless MX FUEL core drill, for example, cores holes up to 6 inches in reinforced concrete.

How do I drill a 4-inch hole in concrete block?

Use a carbide core bit on an SDS-max or spline rotary hammer, or a diamond core bit. Mark the hole over a hollow cell if you can, so you only cut the two face shells. Drill partway from each side to avoid blowing out the far face.

Is it OK to cut rebar in a foundation wall?

One small vent hole through a wall usually clips a bar or two, and wet diamond bits cut it. If you're not sure the wall can take it, or you'll cut several bars, ask a structural engineer first.

What size hole do I need for a dryer vent?

Code calls for a 4-inch nominal round duct. The hole has to clear the outside of the vent hood's sleeve, which is a bit bigger. Measure the sleeve and pick the core bit size that clears it.

Sources

  1. 48-17-5040 4 in. Diamond Ultra wet core bit: wet use only, concrete and rebar, 1-1/4 in-7 thread for MX FUEL and corded core drills (Milwaukee Tool)
  2. MXF301-2CXS MX FUEL handheld core drill kit with stand: up to 6 in holes in reinforced concrete, clutch and AUTOSTOP, water line (Milwaukee Tool)
  3. 48-20-5145 SDS-max and spline thick-wall carbide core bit, 3 in: brick, block, concrete; 4-1/16 in usable depth; guide plate and centering pin (Milwaukee Tool)
  4. 29 CFR 1926.1153, Respirable crystalline silica (construction), Table 1: drills, rig-mounted core drills; (f) housekeeping (OSHA)
  5. Seattle Residential Code 2018 (IRC-based), Chapter 15, M1502.4.1: dryer exhaust duct 4 in nominal diameter (City of Seattle)
  6. Post-tensioning construction basics: cut tendons are hard to repair (Concrete Network)
  7. Post-tensioned concrete cutting hazards: tendons cut by a core drill can release violently (Fire Engineering)

Robert D. Miller. Robert D. Miller writes ToolsLiving's guides on tools, fasteners, adhesives and outdoor power equipment. How we write and check guides →

Change log: Nov 6, 2026: Merged two 2023 archive posts into one guide at a new URL. Fixed the old advice to cut a 4-inch hole with a hammer drill and diamond bit; added tool-by-wall table, pre-drill checks, OSHA controls and the dryer vent code size.

Keep going

A row of twist drill bits in different sizes

Concrete & brick

What works on concrete, brick and block: the right drill, bit, blade, screw anchor and adhesive, plus OSHA's silica dust controls for each job.